Avalon H Series Manual de servicio Pagina 175
- Pagina / 196
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Installation Instructions for 45HW & 47HW Electrified Mortise Locks
BEST ACCESS SYSTEMS
a Division of Stanley Security Solutions, Inc.
3
Installation Instructions for 45HW & 47HW Electrified Mortise Locks
Finishing the door preparation
3 Center punch and drill holes
1 Center punch the necessary drill points. See the
instructions on the template.
2 Drill the holes.
Note 1: To locate the center of a hole on the opposite
side of the door, drill a pilot hole completely through the
door.
Note 2: For holes through the door, it is best to drill
halfway from each side of the door to prevent the door
from splintering.
4 Drill wire channel through door
Caution 1: Check with your local fire marshal
before drilling a fire-rated door. Drilling through
a fire-rated door may void the fire label.
Caution 2: Be careful to drill straight through the
door, making sure the drill does not break
through the face of the door.
1 Remove the hinge nearest the mortise cavity.
2 Using a 3 to 4 foot drill bit, drill a 3/8″ diameter
channel through the upper back of the mortise cavity
to the center of the nearest hinge mortise.
Note: It may be easier to drill halfway from each side of
the door.
5 Prepare door for door status switch
(optional for deadbolt function locks)
1 Locate the centerpoint for the door status switch 2.5″
above the top of the faceplate mortise on the edge of
the door (as shown in Figure 5).
2 Drill a 1″ diameter hole 1 3/4″ deep for the door
status switch.
3 Position the drill so the tip of the bit is approximately
1″ into the hole and the bit is close to the top edge of
the hole. Then drill a 3/8″ channel at approximately a
35° angle from the door status switch hole into the
mortise cavity (as shown in Figure 5).
Figure 4 Drilling the wire channel through the door
Hinge mortise
Figure 5 Preparing for the door status switch
Door status
switch hole
3/8″
channel
- CREDITS/COPYRIGHT 2
- CONTENTS 3
- INTRODUCING THE 40H LOCK 2–1 4
- LOCK FUNCTIONS 3–1 4
- MORTISE CASE PARTS 4–1 4
- TRIM PARTS 5–1 5
- SERVICE AND MAINTENANCE 6–1 6
- 40H Series Service Manual vii 7
- TRIM PARTS 10
- SERVICE AND MAINTENANCE 11
- 48H & 49H LOCKS 11
- GETTING STARTED 13
- 45H & 47H OVERVIEW 14
- Getting Started 15
- 40H Series Service Manual 1–3 15
- 45HW & 47HW OVERVIEW 16
- 40H Series Service Manual 1–5 17
- 48H & 49H OVERVIEW 18
- 40H Series Service Manual 1–7 19
- DOCUMENTATION PACKAGE 20
- TECHNICAL SUPPORT 20
- INTRODUCING THE 40H LOCK 21
- THE ADVANTAGE OF KITS 22
- WORKING WITH TRIM KITS 23
- Introducing the 40H Lock 24
- 2–4 40H Series Service Manual 24
- TRIM ONE SIDE LOCKS 25
- 2–6 40H Series Service Manual 26
- LOCK FUNCTIONS 27
- Lock Functions 28
- 3–2 40H Series Service Manual 28
- LOCK FUNCTION QUICK REFERENCE 29
- Single-keyed 31
- 3–6 40H Series Service Manual 32
- 40H Series Service Manual 3–7 33
- Double-keyed 34
- 40H Series Service Manual 3–9 35
- Deadlocked 36
- Non-keyed 37
- Electrified 40
- MORTISE CASE PARTS 43
- A FUNCTION CASE—OFFICE LOCK 44
- A function case 45
- 4–4 40H Series Service Manual 46
- AT, C, D, INL, R, W 47
- ZD, XR function 47
- LT FUNCTION CASE—PRIVACY LOCK 48
- LT function case 49
- N FUNCTION CASE—PASSAGE LOCK 50
- N function case 51
- NX FUNCTION CASE—EXIT LOCK 52
- NX function case 53
- FUNCTION CASE—HOLDBACK LOCK 54
- CHB, RHB function 55
- AB FUNCTION CASE—OFFICE LOCK 56
- AB function case 57
- B FUNCTION CASE—ENTRANCE LOCK 58
- B function case 59
- FUNCTION CASE—ENTRANCE LOCK 60
- FUNCTION CASE—STOREROOM LOCK 60
- BA, S function case 61
- BW function case 63
- UNCTION CASE—ENTRANCE LOCK 64
- G, B5, B7, function 65
- H FUNCTION CASE—HOTEL LOCK 66
- HJ FUNCTION CASE—HOTEL LOCK 66
- H, HJ, TD function 67
- FUNCTION CASE—INTRUDER LOCK 68
- FUNCTION CASE—DORMITORY LOCK 68
- IND, T case 69
- L FUNCTION CASE—PRIVACY LOCK 70
- L function case 71
- LB FUNCTION CASE—PRIVACY LOCK 72
- LB function case 73
- TA function case 75
- AD FUNCTION CASE—DEADLOCK 76
- WD FUNCTION CASE—DEADLOCK 76
- YD FUNCTION CASE—DEADLOCK 76
- AD, WD, YD function 77
- RD function case 79
- DEL function case 81
- DEU function case 83
- WEL function case 85
- WEU function case 87
- NXEL function case 89
- NXEU function case 91
- TDEL function case 93
- TDEU function case 95
- TWEL function case 97
- TWEU function case 99
- Mortise Case Parts 100
- LEL function case 101
- LEU function case 103
- CASE ONLY LOCKS 104
- 45HCA – R – 626 – RH – 104
- 45HWCA – DEL – 626 – RH – 105
- Case only 106
- OUTSIDE TRIM KITS 108
- Available door thicknesses 109
- Qty. per kit 109
- Trim Parts 110
- 5–4 40H Series Service Manual 110
- 40H Series Service Manual 5–5 111
- INSIDE TRIM KITS 112
- 114
- 40H Series Service Manual 5–9 115
- STRIKE PACKAGES 116
- 40HST – 1 – 626 – 116
- Item Description 1 4 5 117
- LEVER SETS 118
- 40HLS – 14 – 626 – 118
- Part number 120
- FACEPLATE KITS 121
- 40HFP – 3 – 626 – 121
- REPLACEMENT SPINDLES 122
- 40HRS – 2 – 122
- Replacement 123
- SCREW KITS 124
- 40HSK – 1 – 626 – 124
- CYLINDERS AND CAMS 126
- Cylinders by door 127
- Cylinder ring 127
- Figure 5.25 Cylinder rings 128
- Figure 5.26 Cylinder cams 128
- ESCUTCHEON ASSEMBLIES 129
- J trim inside 130
- M & N trim outside 131
- M & N trim inside 132
- ROSES AND ROSE RINGS 133
- DUMMY TRIM 133
- VISUAL INDICATOR TRIM 134
- SERVICE EQUIPMENT 135
- DRIVER BITS 136
- CHANGING THE HAND 140
- Function Hub toggle position 141
- Service and Maintenance 142
- 6–4 40H Series Service Manual 142
- Changing the 143
- UNR cases 143
- TROUBLESHOOTING 145
- 6–8 40H Series Service Manual 146
- FUNCTION DESCRIPTIONS 148
- K, L, M function 149
- 48H & 49H Locks 150
- 7–4 40H Series Service Manual 150
- Figure 7.3 R function case 150
- 48H TRIM PARTS 151
- 7–6 40H Series Service Manual 152
- STRIKES AND STRIKE BOXES 153
- GLOSSARY 155
- Glossary 158
- A–4 40H Series Service Manual 158
- INSTALLATION INSTRUCTIONS 159
- Installation Instructions 160
- B–2 40H Series Service Manual 160
- Installation Instructions for 161
- 45H & 47H Mortise Locks 161
- 2 Align templates 162
- BEST ACCESS SYSTEMS 163
- 8 Install mortise case 164
- Installing the trim 165
- Finishing the installation 171
- 18 Install cores 172
- 19 Check operation 172
- 1 Identify holes 174
- Center punch and drill holes 175
- 8 Install door status switch 177
- 11 Install mortise case 179
- 22 Install cores 187
- 23 Install lock power supply 188
- 24 Make sensor connections 188
- 25 Check operation 188
- 1 Mark centerlines 189
- 2 Mark drill points 189
- 3 Install strike 189
- 7 Install core 190
- 4 Mortise and drill holes 190
- 5 Install mortise case 190
- 6 Install trim 190
- Numerics 191
- C-2 40H Series Service Manual 192
- 40H Series Service Manual C-3 193
- C-4 40H Series Service Manual 194
- 40H Series Service Manual C-5 195
- C-6 40H Series Service Manual 196
© 2020, manymanuals.es. Todos los derechos reservados | 0.170 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales